![]() You can get the IDs with sane-find-scanner -q. To enable the scanner you need to add the product ID and device ID to /etc/sane.d/nf, ie set the usb line to usb 0x04b8 0x0813. Needs cupsys-driver-gimpprint from Universe repository. Works in v6.06 (Dapper) out of box but need to select 3800 from list during install. For 5.10 update to gutenprint 5.0.0rc2 driver (by now synaptic might work or you might have to compile) see Works in 6.06(Dapper) out of box but detects it as 3800 so select 3810 from list during install. When Gimp-Print version does not list this device explicitly as supported, pretend that you have the C62. Using this printer over the network, with Netgear PS121 USB print server, with no problems. Mtink is a tool for Epson printer to check ink level and clean noozle. Needs cupsys-driver-gimpprint from universe repository. The driver is the same, as are the ink cartridges. Essentially the same printer but a year or two newer. Works out of box, but prints much slower than Windows. Does not seem to work over parallel port connection but does work over USB Needs cupsys-driver-gimpprint from universe. Please test and move the results to the table above. They need tested on a currently supported version of Ubuntu. The following printers were tested on Ubuntu versions that have since reached EOL*. Maintenance and Ink Level functionality not working though. Printed properly.Ĭonnected and it worked. After installing epson-inkjet-printer-n10-nx127 from Avasys website, recognised and auto-installed. Printer is not recognised, you could use the driver for Stylus TX110, test page printed properly. Installing PIPS from avansys makes printing work ok, but leaves a process using ~100% CPU after each job which needs manually killing.Įpson Stylus TX110 - CUPS+Gutenprint v5.2.6 Simplified, epson-inkjet-printer-n10-nx127 When a test page is sent, status goes to "processing" and not much more happens. Recognised & driver auto-installed on connection. Originally suggested gutenprint, CUPS drivers made printer spew out paper until manually rebooted. Printing works excellent! To scan, I recommend downloading the appropriate iscan DEB package from Avasys ( http: hen you will get the correct scanner drivers, and a excellent scanning utility as a bonus.ĭid not try scanning yet wireless network printing works well only after installing driver suggested here. "Print Queue will not clear and printer wont respond" Needs the DX3850 gutenprint driver if you want to attempt to install this printer. Scanner requires libsane-extras package to be recognized. Recognized by CUPS, driver installs and test page come out properly. Use the Stylus D68 CUPS + Gutenprint Driver (Don't choose the 'simplified' one though), Scanner instructions Įpson Stylus CX9400F - CUPS+Gutenprint v5.2.3 Works out of the box, both scanner and printer are detected correctly. Printing works out of the box since at least 6.06 (Dapper) but scanning before 7.10? needs details from lsusb added to /etc/sane.d/nf. Ink levels are not reported in Properties, and I could not find a GUI utility in the official repos that works with the C120. One caveat: Built-in ink/toner levels are not reported or not working (System > Administration > Printing > Printer's properties > Ink/Toner levels) use inkblot instead See Ubuntu Forums thread (slightly different than directions for previous versions of Ubuntu)Īuto-detect and install, works out of box. configure sudo make install -> sudo aa-complain cupsd -> install the printer via gnome system-config-printer tool ( Laser CX11NF Sudo apt-get install build-essential libcupsys2-dev ia32-libs -> download the driver from Avasys website -> unpack the archive into a directory -> cd into previous directory -> sudo. Then "whola !" I discovered these drivers upon which I happily got rid of those old pieces of junk and feel quite certain that I will never have to revisit this nonsense ever again.See question #48722 to make printer working ( Laser CX11NF ![]() Out of sheer frustration, I came SOOOOO close today to scrapping my whole updated system in favor of reverting to my OSX 10.5.6 (of which I had absolutely no issues printing at all once I spent a few days finagling and coercing it to work from the previous update) system backup because this time around I just could not get them to work in OSX 10.5.7. In these tough economic times (in case anyone has forgotten), WHY in tarnation should I have to run out and buy a new printer when mine works perfectly fine if/when/ever the system drivers will operate correctly. I grew SOOOOO dag gone sick and tired of having to finagle and coerce the system drivers to work each and every time I updated to the newest version of OSX 10.5 (10.5.7 this time around). I still own/use a very reliable Epson Printer I bought brand new in 1997.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |